How To Set Up A Keg For A Party
How to Set up Up a Kegerator
Last updated on 7/01/2020
After y'all've deliberated and chosen the all-time kegerator for your business, it's time to set up your beer dispenser and offset serving fresh, common cold beer! Nosotros've got step-by-step directions and an instructional video to help yous through the procedure, assuasive you to pour the perfect pint. Use our steps as a general guideline, but e'er refer to your equipment manual for the manufacturer's specific instructions.
Shop All Beer Dispensers
1. Unpackage the Kegerator
- Remove all the packaging from your kegerator.
- If the unit has been transported on its side, let the unit stand upright for at least 24 hours before plugging it in.
- Move the unit to its final location and install it on a level surface.
- Brand sure to provide clearance around the unit for ventilation, per the manufacturer's instructions.
2. Install the Typhoon Tower
One time your kegerator is unpackaged and placed in its final location, you can begin installing the draft belfry. Gather your materials and look for the circular opening on top of the unit.
You'll need the following materials:
- Rubber washer
- Draft tower
- Beer line
- 4 mounting screws
- Air hose
- Tap faucet handle
Follow these steps:
- Place a condom washer on meridian of the circular opening.
- Feed the beer line down through the opening into the interior chiffonier.
- Place the draft tower on meridian of the opening and secure it with 4 mounting screws.
- Feed the air hose into the draft tower from within the cabinet.
- The air hose helps to continue the beer cold as it travels upward the beer line.
- Screw the tap handle onto the tap faucet.
- Connect the tap faucet to the draft belfry.
3. Connect Beer and Gas Lines
You'll need ii lines to prepare your kegerator - the beer line and the gas line. The beer line connects to the keg by way of the keg coupler and delivers cold beer to the tap faucet. The gas line connects to the CO2 regulator on the CO2 tank, then besides connects to the keg coupler.
Depending on the manufacturer of your unit, you may need to purchase some of these required beer dispensing components separately. Refer to your kegerator manual for more information.
Yous'll need the following materials:
- (2) Rubber washers
- Nut
- Keg coupler
- Beer line
- Gas line
- Beer keg
- CO2 tank
- CO2 regulator
Follow these steps:
- Keep the tank upright at all times.
- Adhere the beer line to the keg coupler, placing a safety washer at the connection betoken.
- Attach the gas line to the CO2 regulator output barb and tighten screw clamp.
- Connect the other cease of the gas line to the keg coupler and tighten screw clamp.
- Using a rubber washer and nut, attach the CO2 regulator to the CO2 tank.
- Spiral the coupler onto the keg.
- When the coupler is fitted into place, button the coupler handle down to open the seal.
- Place the keg inside the kegerator.
4. Arrange the CO2 Regulator
With your beer and gas lines in identify, you lot're almost gear up to start dispensing your customers' favorite beers. You'll just demand to make some adjustments to your CO2 tank and regulator to release the gas and make sure it's at the correct pressure level.
Follow these steps:
- Turn the handwheel on the CO2 regulator to the left to open up the air tank.
- Flip the shut-off valve on the regulator to ON.
- You should hear air enter the gas lines.
- Adjust the PSI so the pressure gauge reads between ten and 15.
- Carefully place the CO2 tank into the chiffonier and close the door.
At present that your kegerator is in place and set up to utilise, prepare a schedule to maintain your beer system and ensure your taps and beer lines stay make clean. Audit the CO2 levels on your tank regularly and check the PSI approximate to make sure the pressure is at the right level. With proper maintenance, your beer dispenser will provide many years of service.
Source: https://www.webstaurantstore.com/article/515/how-to-set-up-a-kegerator.html
0 Response to "How To Set Up A Keg For A Party"
Post a Comment